Industrial Networking

About THETA

Theta Controls brings you a wide range of Industrial Networking solutions from the pioneers and market leaders, Hirschmann Electronics, Germany.

Ethernet is now the choice of the network for communication between various industrial controllers and the SCADA, due to its speed and widely available hardware at an affordable price. However, when you are using it in industrial environment, you must use an industrial grade device, and not an office grade one. This is explained below

Dummy Img

Important Characteristics of Industrial Networks

  • Mounting:
    • Since the switches are mounted in control panels, it is more convenient if they come in a DIN rail mounting form factor. The other type commonly used is a rack mount
  • Power supply:
    • Since the switches are mounted in panels, where the predominant supply is 24V, it is desirable if they can accept 24VDC directly
  • Approvals:
    • While most industrial switches come with a minimum of UL or CE marking, there are many approvals required for industry specific application, such as Substation, Trains, Ships, etc
  • Redundancy:
    • Desirable in industrial applications, where a shutdown can result in huge losses. Common type of redundancies are power supply redundancy, media redundancy, whole network redundancy.
  • Interface Fiber directly:
    • Most of the industrial switches allows for direct termination of fiber cables to the switch, instead of using media converter in between. It saves a lot of cost and space. With single mode fiber cable, you can get distances upto 120km without using repeaters in between.
  • Temperature range:
    • Most industrial switches have a temperature range of 0 to 60 deg C, instead of the regular commercial range of 0 to 45 deg C. However, there are switches with a much wider range for specific applications. Industrial Switches are available in various ranges upto -40 to +85 deg C
  • IP rating:
    • While a rating of IP40 is sufficient for switches mounted inside the control panel, there are switches available with IP65 for stringent applications
  • Hot Swappable Modules:
    • Like PLC's, there are switches with hot swappable media modules. There is no need to shut down the whole switch, in case of a media module failure.
  • Fan-less design:
    • Industrial switches are fan-less design which increases the reliability as it has no moving parts unlike the commercial switches, which are fan cooled.

Substation Switches :

MACH1000 :

Ultra-hardened switches, fully configurable operating temperature -40 ‘C to +85 ‘C, optionally for all variants 4 PoE ports

  • MACH1020: up to 24 ports
  • MACH1030: up to 28 ports up to four of which are Gigabit
  • MACH1120: up to 20 ports on rear of switch, up to four of which are Gigabit
  • MACH1040: 16 Gigabit, RJ45/SFP Combo ports, in layer 2 or layer 3 version

GREYHOUND :

Fast/Gigabit Ethernet switches designed for use in harsh industrial environments

  • From entry level types with 16 fast eternet up to 28 ports Full Gigabit Layer 3 Version
  • Field exchangeable media modules
  • Version with hot swap power supplies
  • 2.5 Gigabit uplink and full wire speed layer 3 options

Managed DIN Rail Mount Switches :

RS20, RS30, RS40, RS22, RS32 :

Fully configurable managed switches with selectable

  • features and approvals
  • RS20: 4, 8, 9, 16, 17, 24 or 25 ports
  • RS30: 10,18, or 26 ports, two of which are Gigabit
  • RS40: 9 ports all Gigabits - Upto 4 FO Ports
  • RS22: 4, 8, 9, 16, 17, 24 or 25 ports, four of which are PoE
  • RS32: 10,18, or 26 ports, four of which are PoE, two are Gigabit
  • 2 Uplink can be Fibre ports

MS20, MS30, MSP30, MSP32, MSP40, MSP42 :

Full Gigabit managed modular switches with selectable features and approvals as well as user hotswappable media modules for almost limitless copper/fibre combinations.

  • MS20/30 up to 26 ports, two of which can be Gigabit
  • MSP30/32 HiOS advanced Layer 2 & Layer 3 switch, up to 28 ports, four of which can be Gigabit
  • MSP40/42 HiOS advanced Layer 2 & Layer 3 switch, up to 28 ports, four of which on the first slot can be 2.5 Gigabit

RSP Series :

Hardened managed switches with the new HiOS operating system

  •  RSP: uninterrupted redundancy thanks to PRP and HSR , on all ports IEEE 1588v2 time synchronization, comprehensive security functions, variants with 3 GE SFP and 8 FE ports, up to 7 FE SFP slots, layer 2 and layer 3 versions.
  • RSPS: optional PRP and HSR, on all ports IEEE 1588v2 time synchronization, variants with 6 FE ports, up to 4 FE SFP slots.
  • RSPL: comprehensive security functions, variants with 2 GE combo and 8 FE ports, up to 4 FE SFP slots.
  • RSPE: best-possible investment protection thanks to maximum flexibility provided by the media modules, layer 2 and layer 3 versions

RED25 :

Cost-effective fast Ethernet redundancy entry-level switch supporting PRP, HSR or DLR Offered in two, four-port version:

  • Four FE TX ports
  • Two FE TX ports, plus two FE small formfactor pluggable (SFP) ports

RSR20, RSR30 :

Ultra-hardened switches, operating temperature -40 ‘C to +85 ‘C, DC or AC power input

  • RSR20: 8 or 9 ports
  • RSR30: 9 or 10 ports, two or three of which are Gigabit

RSB20 :

Fast Ethernet RSB switches with basic software version

  • RSB20: 8 or 9 ports
  • Upto 3 FO ports

GECKO :

Lite managed switch

  • GECKO 4TX- 4 ports
  • GECKO 5TX- 5 ports

BOBCAT Series (With TSN) :

The first industrial switch worldwide to provide advanced security and real-time communication through time-sensitive networking(TSN) technology on all ports for standardized Ethernet usage in event the most demanding application

  • BRS 20: Available upto 12 FE ports, four of which are Fiber FE ports
  • BRS BRS 30: Available upto 12 FE ports, four of which are Fiber FE/GE ports
  • BRS 40: Available upto 12 FE/GE ports, four of which are Fiber FE/GE ports
  • BRS50: Available upto 12 FE ports, four of which are Fiber GE/2.5 GE ports

Hi-SCOM :

Managed Full Gigabit PoE/PoE+Switches

  • BN44: Available upto 6 FE/GE ports, 2 of which are Fiber GE ports
  • BN48: Available upto 10 FE/GE ports, 2 of which are Fiber GE ports
  • - IS30: Available upto 10 FE/GE ports 5 of which are Fiber FE/GE ports
  • BN3049: Available upto 26 FE/GE ports, four of which are GE combo ports, 2 of which are Fiber GE ports

Unmanaged DIN Rail Mount Switches :

Spider, Spider II, Spider III :

  • Cost-effective, plug & play
  • unmanaged switches
  • Spider 2,3,5 or 8 Ports
  • Spider 2 or 5 ports with PoE PD
  • Spider PoE Injector
  • Spider II PoE and 4 Standard ports
  • Spider II GIGA 5 or 7 ports, all Gigabit
  • Spider III Standard Line up to 8 ports
  • Spider III Premium Line up to 9 ports
  • Fibre Ports available

RS20, RS30 :

Feature-rich unmanaged switches with selectable port types, features and approvals

  • RS20: 4,8,9,16,17,24 or 25 ports
  • RS30: 10, 18, or 26 ports, (2 are GB)
  • Upto 4 Fiber port available

Control Room Switches :

MACH100 :

Hardened Enterprise-grade switches

  • MACH102: 8TP modular switch, up to 26 ports, 10 fixed ports, two of which are Gigabit (modules available for MM/SM fibre, Rj45, PoE/PoE+ and SFP)
  • MACH102: 8TP-F 10 fixed ports, two of which are Gigabit - Combo ports
  • MACH102: 24TP-F 26 fixed ports, two of which are Gigabit - Combo ports
  • MACH104: All Gigabit, 4 RJ45/SFP Combo ports, and 20 Rj45 ports (4 of which can be PoE)
  • MACH104: All Gigabit, 4 RJ45/SFP Combo ports, and 16 Rj45 PoE+ ports (optional with 2XFP 10G uplink ports)

IP 67 Waterproof Switches :

OCTOPUS :

  • Octopus 5TX unmanaged 5-ports, 12 D-code
  • Octopus 8TX-EEC unmanaged configurable, 8 ports, M12 D-code
  • Octopus 8TX PoE-EEC unmanaged, 8, 16, & 24 ports, M12 D-code
  • Octopus 8M/16M/24M managed, 8, 16, & 24 ports, M12 D-code
  • Octopus 8M-6PoE & 8M-8PoE managed 8 ports, M12 D-code, 6 and 8 of which are PoE
  • Octopus 16M-8PoE & 24M-8PoE managed 16 and 24 ports, M12 D-code, 8 of which are PoE
  • Octopus OS2x/3x: IP65/67; from 8 up to 28 ports; M12 D-core; serveral options available; multi- or singlemode fibre ports, Power over Ethernet with up to 15 PoE/ PoE+ ports, 2 or 4 GE ports M12 X-code, managed or unmanaged types, layer 3 software support, power supply options from 24 to 110V DC and 100 to 230 V AC, certified for trains, ships and for use in road vehicles.

Backbone Switches :

MACH4000 :

High density and high speed backbone switch with layer 3 /routing and speeds up to 10 Gigabit

  • MACH4002: 24G up to 24 Gigabit ports
  • MACH4002: 24G+3x, up to 24 Gigabit ports and three 10 Gigabit XFP ports
  • MACH4002: 48G up to 48 Gigabit ports
  • MACH4002: 48G+3x, up to 48 Gigabit ports and three 10 Gigabit XFP ports

DRGON MACH4000 :

Meets the relevant industry standards, providing
very high operational reliability, ever under
extreme conditions and also long term reliability
& flexibility with all advanced HiOS Layer 3
functions

  • MACH4000: HiOS advanced Layer 2 & 3 switch, up to 48 ports, with four 10 GE ports
  • MACH 4500: iOS advanced Layer 2 & 3 switch, up to 80 port, with Eight 10 GE ports and three 10 Gigabit XFP ports

Industrial Wireless LAN :

BAT Access Points/Clients :

  • OpenBAT family - BAT-R and BAT-F -rugged configurable wireless LAN access points and/or clients
  • BAT450-F rugged compact and lightweight configurable wireless LAN access points and/or clients
  • BAT867-R configurable wireless LAN access point and/or client featuring IEEE 802.11ac
  • BAT Controller WLC for centralized management of large WLAN networks
  • BAT-C Wireless LAN access client
  • Extensive antenna and accessory offering

Security, Firewall and VPN Appliances :

EAGLE/Tofino Xenon :

Network segmentation, VPN and deep packet inspection.

  • Tofino Xenon: Industrial firewall with Stateful Packet Inspection (SPI) and optional Deep Packet Inspection (DPI) for bridged communication.
  • EAGLE20-0400 and EAGLE30-0402: Multiport Stateful Packet Inspection (SPI) firewalls optional Deep Packet Inspection (DPI) in convection-cooled metal DIN Rail housings which support 6 LAN ports – two of which are Gigabit and two SHDSL ports
  • EAGLE One: Industrial firewall providing Stateful Packet Inspection (SPI) for bridged or routed communication combined with a unique Firewall Learning Mode and comprehensive Network Address Translation (NAT) techniques.

Network Management Software :

Industrial HiVision :

  • Network visualization and configuration software with integrated OPC server.
  • Obtain instant visibility of key performance indicators with the Network Dashboard
  • Find faults quickly and achieve timely remediation that improves uptime and security
  • MultiConfig configures hundreds of devices from any manufacturer simultaneously
  • Security Status Visualization
  • The Hirschmann Annual Maintenance Plan is available for cost effective updates
  • Configuration Signature Check monitors changes to device configuration files
  • Alerts are generated when unauthorized changes are made, rogue devices are added or MAC/IP address pairs change

Fiber Convertors :

Hirschmann Fiber- Profibus Conv :

  • Available for Single/Multimode Fiber
  • Available with One/Two Fibers
  • Can form Redundant Ring with Fibers

Hirschmann Fiber- RS485 Conv :

  • Available for Single/Multimode Fiber
  • Available with One Fiber
  • BCan form Redundant Ring with Fibers!

Hirschmann Fiber- Genius Bus Conv :

  • Available for Single/Multimode Fiber
  • Available with One/Two Fibers
  • Can form Redundant Ring with Fibers

Cables & Accessories :

Serial to Ethernet Media Convertors :

IOLAN DS/SDS :

End devices with a serial interface can be easily and reliably connected to ethernet network

Embedded Ethernet :

Switches :

  • EES Embedded EthernetSwitches EES20/EES25 and EESX20 and EESX
  • EES Development Kit

Secure Remote Access Solution :

Secure Remote Access Solution :

A simple and secure way to provide remote network access and diagnostics through a three-component system:

  • GateManager
  • SiteManager
  • LinkManager

Industrial Cellular Routers :

OWL :

Single box cellular routers offering high speed wireless connectivity and remote access options.

  • OWL 3G supports UMTS/HSPA+, GSM/GPRS/EDGE frequency band
  • OWL LTE supports LTE, UMTS/HSPA+, GSM/GPRS/EDGE frequency bands and has rich set of communication interfaces
  • OWL LTE M12 supports LTE, UMTS/HSPA+, GSM/GPRS/EDGE frequency bands and has rich set of communication interfaces, is adherence to the EN50155 standard in a rugged, vibration proof design

Cables & Accessories :

:

  • Belden's fire survival & circuit integrity cables ensures continuous operation of emergency circuits, lowest smoke & zero emission of toxic gases in critical & hazardous applications
  •  Manufactured with a hybrid mica glass tape, highly engineered insulation materials & LSHZ sheath
  • Fire resistance with a high performance which can meet IEC60331, Gb19666, Bs6387, EN50200 etc.
  • Cores & Pairs, Triple or Quad optional

Cables & Accessories :

MIPP :

  • Single Modules: 6 x SC Duplex, 6x LC Duplex, 12x LC Duplex, 4 x Rj45 Keystone Jack unshielded or shielded
  • Double Modules: 12 x SC Duplex and 12 x LC Duplex
  • Accessories: Pigtails

Cables & Accessories :

:

Hardened pre-terminated
and factory tested cordsets

  • RJ45-RJ45, RJ45-M12, M12-M12
  • Unshielded and Shielded Versions
  • PVC, TPE and TPE High-Flex Cat 5e UTP
  • 17 lengths - from 0.3 to 50 meters
  • M12 bulkhead termination also available

Cables & Accessories :

:

  • Power Flexibility - Products available with wide ranging AC or DC input and 24 volt or -48 volt output.
  • Hardened - Units are available with operating temperatures ranging from -40°C to 70°C.
  • Waterproof Units Available - Two Ip67 rated units with -48VDC output are available.

Cables & Accessories :

:

Extending the reach of copper for serial &
fieldbus protocols via fiber

  • Line Flexibility - Fiber, copper SFP transceivers are available. Bi-Directional models may also be selected.
  • Fiber Flexibility - Both single and multimode SFP transceivers are available.
  • Data Rate Flexibility - Fast Ethernet, GE and 10 Gigabit units may be selected.

Cables & Accessories :

:

  • Auto-configuration adapter 64 MB, with USB 1.1 connection and extended temperature range, saves two different versions of configuration data and operating software from the connected switch.
  • Simple plug-and-play - after connecting the ACA, the new switch loads and saves the complete configuration and software
  • No network knowledge required - only connect the ACA and power up the new switch - instantly ready for use
  • Increased flexibility – a wide range of Auto-configuration Adapters that perfectly support Hirschmann’s industrial Ethernet and wireless solutions for reliable performance

Defence Systems

About our Activities

THETA has been developing Controllers and Instruments, mainly for DRDO, for the last 30 years. Many of the units developed by us have gone in production / field use.

We had been involved with the development of ROV 'Daksh' for several years, and had developed several major subassemblies for it. We were also privileged to be selected as one of the 4 production partners for manufacturing complete

Theta is also involved in other projects of R&DE, like the SROV, CSROV, UXOR etc.

We are presently working with multiple users across Various DRDO's, PSU's and also private Defence Manufacturers. We handle development of units as per required specifications, and also manufacturing capabilities to provide required

Dummy Img

Theta has developmental capabilities - as under

  • Embedded Controls –
    • Over the years, THETA has developed various embedded systems for a wide spectrum of applications.
    • We are working on the 8051 family, Microchip, ARM & also Tibbo programmable devices.
  • Power Electronics –
    • We work with Thyristors, MosFETs, IGBT's, etc, and have done various units like the power regulator, specialized power supplies, HV PSU's, Buck Boost converters, etc
  • Analog, Digital and Discrete Logic –
    • These are very useful for signal conditioning, as well as implementing fast logic. We also work on CPLD's
  • Working across Multiple Technologies -
    • We have worked with various technologies like PC systems, Communication, Mechanical Systems, Motor Controls, etc
  • Ruggedization of units –
    • Most of the units developed by us, that have gone in production, have been tested for JSS-55555.

Our Services:

  • Manufacturing to your Design
  • Developing to your circuits
  • Developing to your requirement
  • Any other

Remotely Operated Vehicle (ROV’s) :

SROV :

SROV –System  consists of the following

  • The Surveillance Remotely Operated Vehicle (SROV) is a mini ROV designed for carrying out surveillance covertly, provide video feedback on real time during day or night conditions. 
  • The SROV can be deployed with in buildings for carrying out surveillance during any counter –terrorist or counter –insurgency operations.
  • The Versatile SROV is capable of climbing 165 mm stairs inside the buildings.
  • The SROV is Equipped with Night Vision Camera, Water jet distrupter , and optional Payload of Thermal Imager, charge Drop Assembly.

ROV-Daksh :

Daksh is a remotely operated robotic vehicle for multipurpose applications in hazardous environments. It is designed to  be a valuable equipment for Army/Paramilitary forces in challenging missions. One lot has been supplied for IED (Improvised Explosive Device) retrieval.

ROV-Daksh system consists of the following

  • The main unit: Remote Operated Vehicle  - ROV Daksh
  • Master Control Station (MCS) for ROV
  • A specially designed Carrier Vehicle to carry the Daksh and MCS  to site 
  • Accessories such as X-Ray Machine, Water Jet Disrupter,  Shotgun, Extension arm etc.
  • ROV-Daksh can lift 20 Kg at 2.5 meters.

CSROV :

CSROV –System  consists of the following

  • The Confined Space Remotely Operated Vehicle is a compact Unmanned ROV Designed  to defuse  Improvised Explosive Devices (IEDs).
  • The IEDs ma be located  in urban or forested area during  counter –Terrorist (C/T) and Counter Insurgency (C/I) operations.
  • The CSROV is capable of being remotely controlled over a range of 200 m line of sight. 
  • The versatile CSROV is capable of climbing 22mm/40 deg stair inside building. 
  • It is electrically powered by special batteries and multiple cameras on board for aiding the operator to drive as carry out mission specific tasks.
  • CSROV can lift 8 Kg at 2.2 meters.

Units Developed For Mahindra Defence :

Remote Control Unit :

Local Control Unit :

Units Developed For ROV's :

Remote Digital IO :

  • Works on RS485
  • 24V inputs
  • Relay outputs

Video Multiplexer :

  • Suitable for 8 Cameras
  • Supports Quad Vision and PIP

Drive Unit :

  • Has drives for 2 PMDC Motors and 6 BLDC Motors
  • Command on serial port

Operator Console Unit :

  • Custom graphics
  • 3 joysticks
  • Sends Command on RS232

Cable Drum - Fibre Optic :

  • To send Video, Audio & RS232 Data
  • Length- 200m
  • Can be unwound with signal in live condition

Cable Drum - Electrical :

  • Suitable for 230V, 10A
  • Length- 200m
  • Mains can remain ON, while winding or unwiding

Laser Pointer :

  • Can operate in temperatures  of  -20° C to 50° C
  • Green laser for better visibility
  • Used for aiming shotgun/disrupter

Power Distribution Unit :

  • Generates 12V from the input of 24V
  • Distributes 24V and 12 V to various devices in the RO

Zoom Camera :

Operating Console Unit :

  • Custom graphics
  • 3 joysticks
  • Sends Command on RS232

Master Control Unit :

Units Developed For AERV :

Digital Cone Penetrometer :

  • Gives the compactness of the soil
  • Also informs which vehicle can pass over the terrain

Inclinometer :

  • Gives inclination from -45deg to +45deg
  • Temprature compensated

Ethernet to 8 port Serial :

  • Takes the RS-232/RS-485 signals from 8 instruments and sends them on Ethernet to PC
  • JSS55555 qualified

Water Current Meter :

  • With the sensor supplied measures velocity of water in m/s

Special Test Equipment (STE) :

:

Theta has made Test Equipment for the various equipment it has developed.  Many of them have been supplied to our Customers like R&DE, BEL, Mahindra Defence, as well to the End Users, MOD
We have also made an integrated Test Equipment for MOD, which can test around 10 units which were manufactured by us for ROV 'Daskh'
While most of the test units made are operated manually, we have also made Automated Test Equipment, which are controlled by the PC.  

 

Rugged Ethernet Switch :

:

Theta is a distributor of hirschmann for over 20 years & have the capability of giving complete support for networking solutions, including design. We can now ruggedize those switches for you to conform to JSS-55555 applications, for land and sea. We can offer both managed and unmanaged switches, including PoE ports. 
Developed 

Industrial Automation

Introduction:

Theta Controls & Systems Pvt. Ltd. - the newest entrant to our group is a one stop shop for all Automation and Energy-related requirements. Formed as part of our constant endeavour to reinvent ourselves and to serve our customers better, we decided to merge our complete Automation, Energy and Sensors business under a single entity.

This company is an amalgamation of three business units - Kontrelek Instruments (Autonics), Theta Controls (Process Instruments Division - Brainchild and Jaki products) and Cologicx Systems Pvt Ltd (energy-related test and measurement solutions).

We believe in long-term partnerships with our customers to best meet their needs and requirements on an ongoing basis.

Dummy Img

Process Control :

LCD PID Controllers :

Our atest TH.PID 1 series with many innovations

  • Heater break detection
  • Profile Controller
  • Multiple event inputs
  • Remote setpoint
  • High Accuracy 18 Bit A-D-C Input and 15 Bit-AGropur D-A-C Output
  • True Universal Inputs of Thermocouple, RTD, MA, V
  • Fuzzy+PID Control
  • Possibility of both RS-485 and Analog Transmission
  • Auto Tuning
  • 2 Programs Each With 8 Segments of Ramp & Son
  • Up to 6 Event Inputs
  • CT inputs For Heater-Break Detection
  • High Sampling Rate of 200msec
  • Bidirectional Menu Navigation

PID Controllers :

  • Auto-tuning Auto-tuning/Self-tuning and Fuzzy Logic
  • Inputs: T/C, RTD, MA, V DC, Analog input for Remote Set Point
  • Outputs : Relay/Pulse/mA/V DC, Analog Retransmission Output
  • Optional: RS-485/RS-232 Interface
  • Event input for changing function, set point
  • DAQ software available and can be customized

Profile Controllers :

  • Total 9 profiles with 16, 32, 64 segments at most
  • Each segment to be configured as a ramp or dwell (soak)
  • The fast sample rate of 200 msec
  • Up to three relay are configurable for event output
  • Analog retransmission
  • Optional RS-485 or RS-232 communications
  • DAQ software available and can be customized

HMI :

  • It supports many PLC's like (ABB, GE Fanuc, Siemens etc.)
  • Supports various protocols like Modbus, Ethernet, CAN open, Profibus etc
  • Data logging, bar graphs, trends and alarms.
  • Animation: display/hide, flash, color change.
  • FDA 21 CFR - Part 11 Compliance

IO Modules on RS485 :

  • Many types of IO modules available
  • RS-485 with Modbus RTU protocol
  • Can be used as external channels for PR series Paperless Recorders
  • Add on 10 to existing PLC, HMI & SCADA systems
  • Cost effective Remote IO solution
  • Data Acquisition software available and can be customized

Panel PC :

  • All-in-one device including functions of PLC, HMI, and I/O modules
  • 10.4-inch TFT LCD True Colour display
  • Horizontal / Vertical installation
  • Communication: RS232, RS422/485, Ethernet, CAN, USB, VGA, HDMI, Audio
  • 32 input and 32 output points provided
  • Motion control and high-speed counting function included

Recorders :

Paperless Recorder :

Can have built in PID controls as well

  • Fast logging speed : 100msec sec
  • 2 USB, web server, email, and many more features
  • Supports pulse input, all T/C, RTDs and Linear Inputs
  • Math Channels available
  • 48/24/6 input channels and max upto 96/48/24 external channels
  • IP65 high resolution touch screen display
  • Communication Standard Ethernet - Optional RS-232/RS-485/RS-422
  • DAQ software available and can be customized
  • Can have 1/2 channel PID Controls built in (with Profile controller)
  • FDA 21 CFR - Part 11 Compliance

Hybrid Recorders :

  • Combined functions of paper recorder and paperless recorder
  • Enables to print the saved data of inner memory when running out of recording paper(data logger function)
  • Recorder, 50/100mm, 12 Channel, 12 Alarm output, RS485 Ethernet/USB, 100 to 240VAC
  • High speed sampling of 25 ms, high speed record of 240 mm/H functions
  • Space saving for installation with compact design (rear length: 168 mm)
  • Supports total 27 kinds of input types
  • Enables to order several type input cards (weight, voltage, current frequency, potential meter, etc)

PID/Process Control Card for Paperless Recorders :

  •  PID Controller, Ramp & Dwell Controller and Recorder 3 in one Device  
  •  18-bit Universal input A-D for PID Control  
  •  Fuzzy + PID microprocessor-based control  
  •  50 Profiles,1000 Segments in Total  
  •  Auto-tuning and Self Tuning function  
  •  " Soft-start " Ramp and Dwell timer  
  •  Universal inputs( Thermocouple, RTD, mA, VDC )  
  •  Analog input for remote set point and CT    
  • Event input for changing function & set point

 

Power Controllers :

Theta Power Regulators :

Options available in Phase Angle and Zero Cross control  

  • 4-Wire connection as standard ( 3-wire also available as an option )
  • Built-in protection with semiconductor fuses and snubber circuitry
  • Large Range: 1 phase - 10A to 80A & 3 phase 20A to 350A to meet  a variety of needs
  • Simple, Robust construction long-lasting reliability
  • Very High resolution with Extremely Fast response
  • Minimum maintenance with respect to contactors 
  • Elimination of RFI and Harmonics ( ZCO Range only )
  • Elimination of Arcing   Increased heater life due to lower temperature cycling  
  • Less noise and transients ( ZCO Range only )  
  • Compact size with similar footprint and volume as per comparable  contactor

Jaki Thyristor Power Regulators :

  • 1 Phase or 3 Phase 3 Phase can have Delta / Star without Neutral
  • Available from 20A to 750A    
  • Optional current limiting available  
  • Compact size     
  • CE marking

Digital Thyristor Power Control Unit :

  •  Soft Start (0-100 sec)    
  • Accurate Feedback Control    
  •  Supports Multi-Input Control signal    
  •  Heater Break Alarm Option available at 10 sec period    
  • Modbus RTU Protocol port with RS-485    
  • Supports Local or Remote Display    
  • 6 customizable digital Inputs.
     

Thyristor Switches For Capacitors :

  • Switch for Capacitors used in power factor correction    
  • The bulit-in control unit of turn on / off at zero voltage - no surges
  • Operating voltage 380-480V AC, 3 phase Controller has protection for Phase loss, fuse failure & over heat       Small size, built in fast speed fuse for short-circuit protection
  • Compact size    
  • CE marking
     

1 Phase / 3 Phase SSRs :

  • Wide range of ratings from 10A to 75A in both single and three Phase    
  • Multiple control options for 4-20mA and Voltage control    
  • Integrated Heat sink - Optional    
  • Random turn on, Zero Cross and Phase Angle controls  
  •  Screw and DIN rail mounting options

 

Motor & Drive Solutions :

Magnetic Sensors :

The MGS1600GY is a sensor capable of detecting and reporting the position of a magnetic field along its horizontal axis. The sensor is intended for line following robotic applications, using a magnetic tape to form a track guide on the floor.  

  • Multiple Command Modes - Serial, USB,CAN  
  • Built-in Programming Language.  
  •  Includes a 3-axis Gyroscope    
  • Magnetic tape of  25mm (1")and 50mm (2") width, in 45.7 meter  (150ft) rolls available
     

Brushless DC Motor Controller :

Brushless DC motors run quieter, with reduced wear and higher reliability. They are increasingly the preferred choice in electric vehicle and industrial system. Choose from over 10 product references of single and duall channel controllers ranging from 30A to 150A per channel. All Roboteq controllers share advanced features, including: 

  • High-Efficiency power stage  
  • Regenerative Braking Support  
  • Multiple Command Modes - Serial, CAN, USB, Analog, Pulse  
  • Built-in Programming Language. 

Brushless DC Motors :

Brushless DC or BLDC motors for a wide range of applications.

  • BLDC Motors range from 30 watts to 1500 watts
  • High-Efficiency power stage    
  • Higher torque & efficiency, longer life, increased reliability  
  • Much lower electromagnetic interference (EMI)  
  • Require very little or no maintenance  
  • Can be supplied with reduction gearbox

PMDC / Brushed DC Motor Controller :

Permanent Magnet / Brushed DC motors are the most common and least expensive motor types. Chose from over 30 product references of single and dual channel motor controllers for brushed DC motors, ranging from 20A to 500A per channel. All Roboteq controllers share advanced features, including:       

  • High-Efficiency power stage  
  • Regenerative Braking Support    
  • Multiple Command Modes - Serial, CAN, USB, Analog, Pulse    
  • Built-in Programming Language 

PMDC / Brushed DC Motors :

Brushed DC or PMDC motors for a wide range of applications.

  • PMDC Motors range from 30 watts  to 1500 watts  
  • High-Efficiency power stage  
  • Higher torque & efficiency, longer life, increased reliability  
  • Can be supplied with reduction gearbox
     

Stepper Motor Drives :

  •  High torque & high speed performance.  
  • Bipolar constant-current    
  • Self-diagnosis function  
  • Full & half step and micro step
     

Stepper Motors :

  •  Compact design and light weight  
  •  High accuracy, speed and torque  
  • Available in 42mm and 56mm size  
  • Available Torque from 0.206 Nm to 1.5 Nm

 

Accessories :

Serial to Wi-Fi Convertors :

  • 5 GHz frequency support to reduce interference  on 2.4 GHz with other wireless devices
  • Convert RS232/RS422/RS485/USB signals to Wi-Fi for wireless transmission up to 100m
  • Compact size    
  • Surge protection and Reverse polarity protection
  • Various mounting methods (DIN rail, screw mount)

USB TO RS-485 Convertors :

  • Converts USB signal to RS-485 signal  
  • Compatibility with USB 1.1 and USB 2.0    
  • Compact design

Sensors,Transmitters and Interface Modules :

No Control system is complete without the correct set of accessories. For the convenience of our customers, we carry an entire range of accessories that are required to interface with our systems. Each of these products provides a high level of Accuracy, Quality and is tested with the unit it will be used with. For higher accuracy requirements, the Sensor and the Required unit (Recorder / Controller) can be calibrated as a set and NABL certification for the same is also available. Some of the products usually required with these systems that are available with us are listed below: 

  • Temperature - RTDs / Themocouples  
  • Pressure - Sensors / Transmitters  
  • Voltage, Current, Power Transmitters  
  • Interface / Isolation modules  
  • Power Supplies 

Solutions :

Furnace Control Panels :

  • Custom panels with all requisite protections from the control  experts   
  • Complete copper Bus Bars / Cables  
  • Improved reliability through properly designed ventilation  
  • Multiple control / monitoring options can be integrated into the  system

HMI / Paperless Recorder Panels :

  • Customised panels in MS/SS to meet diverse industrial needs  
  • Transparent doors / covers to protect the equipment when not in use  
  • Equipment is terminated into terminal blocks for ease of wiring and   to avoid any damage to the equipment during commissioning / wiring    
  • IP5X / IP6X panels as required  
  • Variety of termination and interconnection options for  Communication (Ethernet / RS-485), Sensor input connectors, etc   

Portable I/O Simulators :

  • Customised as per application / unit to be tested
  • Highly robust design with an industrial-grade plastic casing
  • Can simulate and monitor Analog as well as Digital IOs for field testing
  • High channel count in a compact package
  • Can be used for - AMF Controller, Simple PLCS, Customised controllers
  • Wide-range supply 100-300 VAC

Portable Paperless Recorders :

  • Brainchild's feature-rich Paperless recorder in a Portable, Industrial  grade case  
  • Multiple 3/6/12/18/24++ Temperature / Analog channel options with  true universal inputs  
  • AC/DC Power supply (Built-in Battery optional)  
  • Self-contained unit with all sensors / accessories and cables in  one  case  
  • Panel-mounted  Ethernet / RS-485 port    Analog Outputs / Digital Inputs / Outputs  
  • Product Featured

                - 12 Temperature Inputs

                - 10 Thermocouple + 2 RTD        

                - 12 Pressure Sensor Inputs        

                - Dual Power Supply - 230 V AC OR 11 - 36 V DC

                -High-speed Pulse input ( 4,500 Hz+)        

               - DC Voltage measurement          

              - Provision for Ethernet and RS485 connections

               on the front panel

Field Testers - Temprature / Pressure :

  • Portable testers for operation of temperature and pressure sensors/switches in the
  • Compact capable of upto 10 bar pressure or 100 °C temperature in the field
  • Can be customised for specific sizes / thread patterns of sensors to be tested
  • Only temperature pressure testers can also be provided
  • Compact Size 500 400 x 200 mm. Light Weight <6 Kg

CGX-kWh-03 Multifunction Meter :

Measures Active, Reactive, Apparent Energy, Power and THD, along with all the other energy parameters-V1, PF etc.

  • THD upto 15th harmonic
  • Onsite Programmable system configuration 3Ph4W/3Ph3w/1Ph2w
  • Programmable CT ratios and PT ratios Onsite and Remotely (via RS485)
  • Large, white backlit LCD for clearer readings in small frame of 96 x 96 x 55 mm
  • Highly accurate true RMS measurement as per IEC 62053
  • Multiple output options- RS-485/1-Pulse Relay/2-Pulse Relay
  • Can display 67 parameters on screen & measures 130+ key parameters which are available over RS485

CGX-ANA-03 :

  • High Accuracy options - Class 0.5 and Class 0.2
  • Usable for both 3Ph4W/3Ph3W applications
  • High brightness 3-Line LED display
  • Versatile applications with configurable Output options - Upto 2 x 4-20 mA
  • Output, 2 x Relay Outputs, 2 xPulse Outputs, Ethernet and / or RS-485
  • Measures and displays 48 different electrical parameters
  • Low back depth of 80mm despite multiple outputs
  • Import/Export Energy Measurement

EGCP Series AMF Controllers (Model EGCP-03, EGCP-04T) :

  • 3 phase AMF Controller module (can also be used in 1 phase)
  • Senses 3 phase mains as well as DG line current, voltage, frequency, PF and energy.
  • Sensing inverter battery & cabin temperature for telecom sites (EGCP - 04 T)
  • 45 programmable parameters for control, safety and testing
  • 11 Digital Inputs (Optically-Isolated) & 12 Digital Outputs (Optically-isolated) Isolated)
  • Customization and OEM Supplies available
  • Compact 96 X 192 X 80mm frame size
  • Large 16 X 4 LCD for better readability
  • Wide working voltage: 6.5-15V (12V Version)/7-30V (24V Version)

Non Contact Vibration Sensor/ System :

  •  Non contact measurement of vibrations
  •  Sensor is at fixed distance of 200 mm away from objects - can be customized to operate at lower distance up to 50 mm
  • Gives an analog output of vibration
  • Can connect to PC to give frequency + amplitude of vibration
  •  Can measure Amplitude upto 5 mm & frequency up to 1 KHz

Non- Contact Diameter Scanner :

  •  Unit measure the diameter of the object
  •  Non contact and continuous measurement
  •  Suitable for Object size from 1 mm to 30 mm n Accuracy of measurement- 5 Microns Application
  • Online measurement of dia of wire / metal being drawn / extruded
  •  Checking ovality of object
     

Sensors and Control Panel Accessories :

Counters / Timers :

  • Power Supply - Battery, AC or DC  Size - 24x48 to 96x96 mm  
  • Display - White LCD, LCD, LED     NPN / PNP selectable      
  • Analog and Digital Options    
  • Flexible operation with multiple operating modes    
  • Wide Time setting range from 0.001 second to 99999.9 hours    
  • Prescale setting for display in required units ( Length, Volume, Position, etc)  
  • Output relays available for preset conditions
     

Pressure Sensors and Transmitters :

  • Suitable products to measure Pressure in Gas, Liquid      or Oil  
  • Wide pressure range -  from 1 bar to 600bar      
  • Temperature range upto -40°  to 125? (as per product selected)  
  • SS 304 / 316L body options for high corrosion resistance    
  • Compact size    
  • Output DC 4-20mA / 1-5VDC / Relay  
  • Built-in reverse polarity protection circuit    
  • Connector types - Cable, DIN43650-A, DT04-3P, M12, Head  
  • Thread sizes - G3/8, G1/4, R1/2    
  • Feature-rich Pressure Sensors - Zero-point adjustment, Peak value, Chattering prevention 

Measurement and Indication (Indicators / Panel Meters / Display Units) :

  • Display options for Voltage, Current,    
  • Frequency, Pressure, Temperature, Pulse  Display - Bar Graph, White LCD, LCD, LED      
  • Input Signal - Direct Connection, Current      
  • Transformer, DC Shunt, RTD/Thermocouple, 4-20mA, RS485    
  • Retransmission and Relay output options with upto 11 output modes
     

Rotary Encoders :

  • Type - Incremental, Absolute (Single and Multi-turn)  
  • Resolution Options (upto)  
  • Incremental     - 8,000 ppr  
  • Absolute           - 10-bit (1,024 divisions)  
  • Multi-Turn        - 23-bit (10-bit Single Turn + 13-bit Revolutions)  
  • Sensing Method - Magnetic and Optical options  
  • Output interface: Line Driver, Voltage, Totem Pole, Sine Wave, Parallel, SSI, Binary, BCD  
  • Size: 18mm to 100mm  
  • Shaft: Solid, Hollow, Hollow Blind  
  • Termination: Cable, Connector options with upto 11 output modes
     

Door / Area Sensors :

  • Automation of Doors and Production-Line sensing and control    
  • Upto 7m Sensing range    
  • Sensing in High Ambient light and Dusty conditions    
  • Straight beam and cross-beam options 14 configurations (Number of Beams: 4 to 20 / Pitch: 40, 80 mm / Detection area: 120 to 1,040 mm)    
  • Easy installation    
  • Mutual interference prevention , self-diagnosis    
  • Bright LED indicators on emitter and receiver  
  • Plastic and Metal body options    
  • Sizes from 140mm to 1,000 mm

Interface Units :

  • Range of interfacing options to simplify  interfacing and wiring of Sensors, PLCs, Relays and Power Wiring    
  • Ease of Maintenance with necessary   indications and minimised wiring  
  • High Durability and Reliability    
  • Screw / Screwless connection options  
  • Reduction of excess components like Power  Supplies and Short Links
     

Optical Sensors (Colour Mark / Photoelectric) :

  • Compact sensors with options for diverse applications  
  • Sensing distance upto 30m  
  • Excellent Noise immunity and sensing accuracy  
  • Metal / Plastic body options  
  • Sensor Types - Standard, Compact, Ultra-Compact, Oil    
  •  Resistant, Liquid Level, Mirror tape

Control Switchgears and Accessories :

  • Entire range - Selectors, Push Buttons, Pilot / Indicator Lamps, Tower  Lamps, Dome/Signal Lamps  
  • High Quality Durable products    
  • Wide range of Sizes - 16mm, 22.5mm, 30mm  
  • Differentiating Design Features - Square Indicators/ Push Buttons, Shark fin Selectors
  • Clip-on contact blocks for easier insertion and removal

Surge Protection Devices :

  • High discharge capacity thanks to powerful zinc oxide varistors / spark gaps    
  • Quick response  
  • AC / DC line protection options   
  • Poles - 2, 3, 4    
  • Voltage - Upto 1200 VDC and 420 VAC  
  • Discharge Current Upto 120 kA Max / 60 kA Nominal    
  • Fault indication by green / red mark in the inspection window and via remote signalling    Slim Modular design according to DIN 43880    
  • Multifunctional terminals for connecting cables and busbars    
  • Complete unit with plug-in protection modules for easier replacement 

System Integration

About Us

With expertise in several aspects of engineering technology, THETA has developed and delivered wide variety PC based solutions to numerous customers in various industry segments.  

TMCS Pvt. Ltd. is associate company of Theta Group of companies and a Silver Alliance Partners of National Instruments. We have 20 years of experience in building NI hardware based systems & have over 1 million man hours of experience right from LabVIEW 5.0 till date

We provide End to end Solutions:

  • Application software development in LabVIEW
  • Experience in handling and integrating different types of systems
  • Have worked with NI & third party hardware
  • We can develop Custom protocols for serial ports
  • We have made custom cables, custom interface board and custom controllers
  • In-house hardware development of “Glue-logic” for system optimisation
  • Circuit designing expertise
  • Panel building to integrate all component

Our Activities:

  • LabVIEW Development Services
  • Data Acquisition Systems (DAQ)
  • Panel Engineering Services
  • Automated Test Equipment / End of Line Tester (EOL) 
  • NI Hardware Trading 
Dummy Img

Automated Test Equipment / End of Line Tester (EOL) :

Automated Test Equipment / End of Line Tester :

Motor, Alternator Test System:

  • Control and log data of alternator under test.
  • Various tests like voltage regulation, temperature rise test etc can be  carried out automatically
  • Automatic inductive and resistive  loading of the alternator
  • Report generation 

Shock Absorber Test System: 

  • Calculates compression and tension values of a shock absorber.
  • Plots online graph
  • Generates final result based on the tolerance band set by the user 

Electrical Contactor Test Bench: 

  • 6 station test bench
  • Test different characteristics of Electrical Contactor
  • Test parameters are user configurable 

ECU Tester

  • No. of ECU's tested simultaneously.
  • Improve existing and future control units 
  • Reduced time to detect and diagnose failure 

Car Door Handle Tester :

  • LabVIEW made the system adaptable for future software modification
  • Continuous sampling , 20m sec sampling rate
  • Reduced testing time by almost 50 percent 

 Gear Box Testing:

  • Gear shifter lever will be operated with the help of motor.
  • User needs to teach the path to follow gear sequence.
  • Different parameters will be  captured during this endurance test

 Body Control Module :

  • Ensuring Safety, testing and control of electrical load parameters.
  • Maintaining Communication between integrated control unit through CAN or Ethernet n
  • Improved productivity. Faster cycle time  

Ultra High Speed Switch tester :

  • 32 Voltage channnels at 6 micro seconds data logging
  • Real time OK -Not OK Monitoring of all channels
  • Reduced testing time increased efficiency
  • High Scanning Rate as 6 Microseconds 

Cluster Tester:

  • Performance test, Endurance test for vehicle electronics
  • CAN Communication Interface
  • Provision for future expansion, store test data into a different database

Generator test system :

  • 1.2 MWatt Generator is tested with back to back loading
  • Futuristic design
  • Analysed reports are generated in prescribed formats 


 

Data Acquisition Systems (DAQ) :

Data Acquisition Systems (DAQ) :

Chiller monitoring System:

  • A distributed system monitors and maintains  various parameters of climatic chambers like temperature, pressure, energy, flow of refrigerant etc. 

Customized of Power Analyzer: 

  • Data Acquisition system specially developed for compressor monitoring 

Crank Shaft hardening: 

  • Data for manifold voltage, Current KW, Energy is captured live during hardenig of a job, based on the master data , result will be generated as Pass or Fail

DAQ for Gear profile :

  • The system checks the Gear Profile with NI and PLC hardware
  • Data from Servo drives, Motors is processed and analysed
  • Software will capture encoder signal and convert it into the angle  compare it with the set value to give Ok not OK Signal
  • All data is acquired, processed and controlled in LabVIEW by Ethernet / serial communication and result will be displayed on the screen in the prescribed format

DAQ for PID :

  • Connect any make PID's,  configure them over Modbus and start using the software

Temperature and Energy monitoring system:

  • Temperature data logging from sensors like RTD, Thermocouple etc.
  • Energy monitoring from different make energy meters or power analysers like Yokogawa, Rishabh, Schneider etc.

DAQ for flow meter calibration

  • Different type of flow meters can be calibrated on each station
  • The required flow will be controlled through different electric control valve adjustment based on data acquire from related master meter
  • Report generation for analyzed data 

DAQ for Calorimeter

  • The Test Stands systems are designed   to allow endurance testing of compressors under extreme conditions
  • Pressure, Flow parameters are tested in LabVIEW environment n Analysed data is available in prescribed Tabular and graphical format

Distributed Gauging system:

  • Used for vehicle Engine Head and Block are measured and logged
  • Different operator stations
  • Data logged centrally on server
  • User can do SPC analysis of the stored data with same software
  • Online Cp, Cpk values will be shown to the operator for easy and handy testing

IIoT 4.0 Enabled Solutions :

NI Hardware Trading :

 

  • Consultation in hardware selection according to project and end user requirement
  • Better  delivery Schedules
  • Timely aftersales Service

Control Panel Engineering services :

:

  • CAB -EOL tester for  automotive  manufacturig giant .Customised Control Panel Designeing , engineering,manufacturing, errection commissioning  for multinational companies. Inhouse and onsite testing
  • AERO Pump test rig -for  Aerospace Application

 

IoT Components

About Us

THETA bring you a range of IoT devices & units as well as useful Development Tools from Tibbo Technology.

What THETA can do for you the pioneers in developing serial-over-IP (SoI) controllers (a.k.a. “device servers” or “serial-to-Ethernet converters”), modules, and related PC software. Tibbo’s SoI products remain popular to this day.

Tibbo undertook to become a leader in hardware and software solutions that simplify and speed up the creation of IoT and automation devices.

Dummy Img

Our Range includes:

  • Programmable Embedded Controller
  • Programmable IoT Modules
  • Serial to Ethernet Converters
  • Universal Programmer / Gang Programmers

Our Services:

  • Supply of Components
  • Technical Support
  • Training
  • Development of your Application Software
  • Development of Custom Hardware

Network Enabled IoT Embedded Modules :

:

Brought to you by TIBBO Technologies, Taiwan.
A powerful range of cost-effective, easy-to-use, Basic & C Pro
time.

  • Simple programming language - Tibbo BASIC C
  • Event driven programming
  • Integrated development system (TIDE) available - FREE

- Easy to upload / download program
- Easy to debug program without any additional hardware

  • Built on our own TiOS. No Royalty or Licence fee
  • New devices to be added continuously

Features

  • Upto 4 serial ports
  • Ethernet 100 Base T Port (Built in TCP/UDP stack)
  • Upto 56 DIO Lines
  • Real Time Clock
  • 1MB for IOS/code + 1 MB for file system vs IBM for IOS, code & File system

For more details & TIDE download visit - www.tibbo.com

Serial to Ethernet - Modules & Divces :

EM 203+ RJ45 :

EM 500/510 :

EM 100-04 :

DS 1102 :

RS232/422/485/ MODBUS Port

DS1100 :

RS232 Port

DS1101 :

3.5 - RS232 Port

Tibbo Project System (TPS) :

Rapid Prototyping of Hardware :

Normally, for any project, there is a need to quickly prove the system, without having to wait for hardware development. And, athe
required quantity is small, it makes even less sense to develop/procure/ debug the hardware

Presenting TPS. It is a modular system. Just assemble the I0 modules in the empty slots of the base board, to
choose the functionality you need. No soldering, no drilling, And put the whole PCB in the enclosure your unit can be ready for trais

in less than an hour

You have two options of base boards (which includes Tibbo programmable controller and a power supply) and a wide variety
of O Modules to choose from. You even have a sturdy exercise to go with it.

The Tibbo controller programs in Tibbo Basic or "C" or both

PCB Boards :

Enclosures :

IO Modules - Over 50 type available :

Development Tools :

:

IO Ninja

A Professional, scriptable, multi-purpose terminal emulaor, network sniffer and IO monitor

:

I2C/SPI Tap

Taps and monitors I2C and spi communications

:

Serial Tap

Taps and monitors RS232, RS485, & TTL-level UART communications

:

Web232/485 board

works as standard USB-to-RS232/485 adaptor, but with WebUSB support

Digital Microscopes

Introduction:

Dino-Lite digital microscope provides a powerful, portable and feature rich solution for microscopic inspection at up to 900x magnification with variety of resolutions. With high quality imaging optics you can easily see magnified images instantly onto your computer or projected onto large screen. A wide range of stands and accessories completes the product line-up and ensures that the Dino-Lite range offers solutions to meet the needs of the home user, through to the most demanding professional.

This is just one small example of the many ways our products redefine the microscope. Over 150 models available to choose from that will exceed your expectations

Dummy Img

Key Features:

  • Handheld and Portable Design
  • Resolution:
    • VGA, 1.3 MP & 5 MP
  • Magnification Range:
    • 5x-900x
  • User Friendly Software:
    • DinoCapture
  • Interface:
    • USB (2.0 & 3.0), TV, D-Sub & DVI
  • Variety of Lights:
    • LED, UV, IR and many more
  • Short Focus & Long Focus:
    • 5.9mm (min.) to 480mm (max.)
  • Reflection control trigger ( Polarizer ):
    • Useful for suppressing glare from any reflective surface.
  • Auto Magnification Reading (AMR):
    • DinoCapture software automatically detects and displays the magnification and stores it with picture.
  • Extended Depth of Focus:
    • EDOF capture model can take several pictures at different focus and stack them automatically within a click.
  • Various Measurement Tools:
    • Line, Radius, Diameter, Angles, Center Distance and many more.

5MP :

Dino-Lite Edge 3.0 :

Dino-Lite Edge :

Dino-Lite Premier :

1.3MP :

Dino-Lite Egde :

DinoLite Egde PLUS :

Dino-Lite Premier :

VGA :

VGA :

Accessories :

RK-04 :

The RK-04 is Robust, lightweight and compact rack design. The Dino-Lite RK-04 rack is designed with portability and convenience in mind

RK-06 :

The Dino-Lite RK-06 tabletop stand is designed for general purpose but built with quality. With smooth focus adjustment and quick vertical movement. The ease-of-assembly and adaptable extension arm design adds further mobility and flexibility to user’s applications.

RK-05 :

If you want to observe your object or specimen from a different perspective, the Dino-Lite RK-05 stand provides a multi-angle view with its 30 degrees inclinable pole feature. RK-05 is a light-weight, ultra-portable stand with a one-step assemble/disassemble design.

RK-10 :

The RK-10 features a quick release button for fast and convenient vertical movement and a fine-focus adjustment knob that is especially useful at high magnification. This model also includes an adjustable safety stop that helps prevent accidental collisions between the microscope and the object under view.

RK-02 :

The RK-02 is a durable gooseneck rack designed for flexible and ergonomic usage for Dino-Lite. The C-clamp of RK-02 fits to most desk surface or pole up to 3-inch in thickness, horizontally or vertically. With excellent shaping capability of the gooseneck arm, the Dino-Lite can be easily positioned by bending the arm and by adjusting the rotating head.

MS52B-A2 :

 Articulating flex-arm and desktop base rack for tightening and positioning the arm for examining 360 degree rotation with microscope.

MS23B :

 An articulating desktop clamp allows you to clamp a stand onto a tabletop or attach to any surface up-to 3cm thick.
 

MS35B :

Is economical and rigid vertical desktop stand designed in such a way that it gives 360 degrees of horizontal axis rotational perspective.

Applications :

Industrial Microscopes :

PCB Microscopes :

Medical Microscopes :

Dermatology / Nail Circulation / Iridology / Trichology / Laboratory / Veterinary

Laboratory Microscopes :

Forensic Science Microscopes :

Hobbies / Jewellery / Coins / Stamps / Antiques / Art restoration / Culture preservation

Natural Science Microscopes :

Educational Microscopes :

Jewerly/ Collectibles :

UV 395nm With MSAA502 :

Without Fluorescence and With Fluorescence :